.: N900 Formatting and Flashing :.
Required Pro
1-Maemo Flasher 3.5 - 2.5.2.2 Download Here
2-Flash File (eMMC Content) This File Earse All Files At Mass Memory (32GB)
3-Main Flash File (OS 2009)
Let's Start
1-Go To This Web Address
2-Write Your Device S.N And Press Send
5-Install Maemo Flasher
6-Take Flash File To This Path c:program filesmaemoflasher-3.5
*Make Sure Battry Is Full
8-Switch Off Your Device Remove Battry And Put It Again
9-Plug USB Cable In Computer
10-Press And Hold (U) On KeyBoard
11-Plug Cable In Your Device
*N900 And Nokia Logo Will Apper On Screen
*You Can Now Release (U)
*Back To Computer
12-Open Start Menu -->Run-->Cmd-->OK
*This Window Will Apper
13-Write This Command CdProgram FilesMaemoFlasher-3.5
14-Then Write
flasher-3.5 -F RX-51_2009SE_1.2009.42-11.203.2_PR_F5_203_ARM.bin -f
This Is Flashing Command
Wait For 5mn
Now Your Device Is Flashing Done...Like This Screen
To Make Hard Reset Follow Same Previous Steps Expect No.14
Change It To...
flasher-3.5 -F RX-51_2009SE_1.2009.41-1.VANILLA_PR_EMMC_MR0_ARM.bin -f
Like This Screen
Congratulations
Now You Can Unplug Your Device
.: Arabic For New Nokia N900 :.
Install It
Go To Application Manager ---> Download ---> All
Find Arabic Localization And Install It
Go To Setting And Choose Arabic Languge
Device Will Restart
Congratulations Your Device Is Arabic
.: About Maemo Flasher :.
Flasher-3.5 - Maemo Flasher Tool
SYNOPSIS
Usage: flasher-3.5 [OPTIONS]
DESCRIPTION
The flasher tool is used to flash data to the Maemo device internal
256MB of NAND, which is where the bootloader, kernel, and rootfs (all
of which make up the operating system) are stored. Flasher can be used
to upgrade the firmware, wipe the Maemo device and start from scratch,
flash certain specific components, or change a number of hardware flags.
OPTIONS
-F, --fiasco=ARG Location of a FIASCO image
-k, --kernel=ARG Location of kernel image
-n, --initfs=ARG Location of initfs image
-r, --rootfs=ARG Location of root JFFS2 image
--cmt-2nd=ARG Location of CMT FIASCO 2nd image
--cmt-algo=ARG Location of CMT FIASCO algorithm image
--cmt-mcusw=ARG Location of CMT FIASCO MCUSW image
--cmt-no-verify Disable verification of CMT programming
-x, --xloader=ARG Location of X-Loader image
-s, --secondary=ARG Location of NOLO secondary bootloader image
-2, --2nd=ARG Location of NOLO cold flasher ("2nd") image
-u, --unpack[=ARG] Unpack a FIASCO image
-f, --flash Load and flash all supplied images
-l, --load Only load all supplied images
-b, --boot[=ARG] Boot the kernel with optional cmdline
-R, --reboot Reboot the board (e.g. after flashing NOLO)
-i, --read-device-id Print out the device type
-S, --serial-port=ARG Serial port used for cold flashing or "usb"
-I, --init-port Only initialize the serial port
-c, --cold-flash "Cold flash" the device
-h, --hw-revision=ARG Specify product code and HW revision
--enable-rd-mode Enable R&D mode on the device
--disable-rd-mode Disable R&D mode on the device
--set-rd-flags[=ARG] Set R&D mode flags on the device
--clear-rd-flags[=ARG] Clear R&D mode flags on the device
--query-rd-mode Query the device R&D mode status and flags
--set-hw-revision[=ARG] Set HW revision override on device
--flash-only=ARG Flash only certain components
-U, --usb-device=ARG Specify USB device to use (bus:device address)
Valid --flash-only options:
nolo, kernel, initfs, rootfs
Valid --set-rd-flags and --clear-rd-flags options:
no-omap-wd
no-ext-wd
no-lifeguard-reset
serial-console
no-usb-timeout
sti-console
no-charging
force-power-key
Latest official downloads are available from Here
Old downloads are available from Here
